How to replace the parts of the yeson vaporizer?

As a supplier of Yeson vaporizers, I often receive inquiries from customers about how to replace the parts of their Yeson vaporizers. In this blog post, I'll provide a comprehensive guide on replacing the parts of Yeson vaporizers, specifically focusing on the Yeson 2 Dry Herb Vaporizer and the Yeson 3s Dry Herb Vaporizer.

Why Replace Parts?

Before diving into the replacement process, it's important to understand why you might need to replace parts of your Yeson vaporizer. Over time, regular use can cause wear and tear on various components. For example, the heating element may lose its efficiency, the mouthpiece can accumulate residue and become less hygienic, or the battery may no longer hold a charge. By replacing these parts, you can extend the lifespan of your vaporizer and ensure a consistent and high - quality vaping experience.

Tools You'll Need

• Screwdriver Set: Different Yeson vaporizers may use different types of screws, such as Phillips or Torx. A set of screwdrivers with various sizes will come in handy.
• Cleaning Tools: Cotton swabs, isopropyl alcohol, and a small brush can be used to clean the new parts before installation and the areas where the parts will be installed.
• Anti - static Wrist Strap (Optional): When working with electronic components, an anti - static wrist strap can prevent static electricity from damaging sensitive parts.

Replacing Parts of the Yeson 2 Dry Herb Vaporizer

Battery Replacement

1. Power Off the Vaporizer: Make sure the Yeson 2 Dry Herb Vaporizer is completely turned off to avoid any electrical hazards.
2. Locate the Battery Compartment: Usually, the battery compartment is located at the bottom or back of the vaporizer. Use the appropriate screwdriver to remove the screws securing the compartment cover.
3. Disconnect the Old Battery: Carefully disconnect the wires attached to the old battery. Take note of how the wires are connected, as you'll need to connect the new battery in the same way.
4. Install the New Battery: Place the new battery in the compartment and connect the wires according to the markings or the way you removed the old battery.
5. Replace the Compartment Cover: Put the compartment cover back on and secure it with the screws.

Heating Element Replacement

1. Remove the Chamber Lid: Unscrew or gently pry off the lid of the herb chamber.
2. Access the Heating Element: Once the lid is removed, you can see the heating element. There may be some small screws or clips holding it in place. Use the screwdriver to remove the screws or carefully release the clips.
3. Remove the Old Heating Element: Lift out the old heating element from its position.
4. Clean the Area: Use a cotton swab dipped in isopropyl alcohol to clean the area where the heating element was located.
5. Install the New Heating Element: Place the new heating element in the correct position and secure it with the screws or clips.
6. Replace the Chamber Lid: Put the chamber lid back on.

Mouthpiece Replacement

1. Remove the Old Mouthpiece: Simply pull the old mouthpiece off the vaporizer. It is usually a snug fit, so you may need to apply a little force.
2. Clean the Mouthpiece Connection: Use a small brush to clean any residue from the area where the mouthpiece connects to the vaporizer.
3. Install the New Mouthpiece: Push the new mouthpiece onto the vaporizer until it fits securely.

Replacing Parts of the Yeson 3s Dry Herb Vaporizer

Display Screen Replacement

1. Power Down the Vaporizer: Ensure the Yeson 3s Dry Herb Vaporizer is turned off.
2. Open the Case: Use the screwdriver to remove the screws on the back or side of the vaporizer to access the internal components.
3. Locate the Display Screen: Identify the display screen and the wires connected to it.
4. Disconnect the Display Screen: Carefully disconnect the wires from the display screen.
5. Remove the Old Display Screen: Gently lift out the old display screen from its mounting.
6. Install the New Display Screen: Place the new display screen in the same position and connect the wires.
7. Close the Case: Put the back or side cover back on and secure it with the screws.

Air Path Replacement

1. Disassemble the Vaporizer: Remove the mouthpiece, chamber lid, and any other removable parts to access the air path.
2. Locate the Air Path: The air path is the tube or channel through which the vapor travels. It may be connected to other components with small clips or fittings.
3. Remove the Old Air Path: Carefully disconnect the old air path from the other components.
4. Clean the Surrounding Area: Use isopropyl alcohol and a cotton swab to clean the areas where the air path was connected.
5. Install the New Air Path: Connect the new air path to the appropriate components and make sure it is properly seated.
6. Reassemble the Vaporizer: Put all the removed parts back on.

Tips for Part Replacement

• Refer to the User Manual: The user manual that comes with your Yeson vaporizer contains detailed information about the internal structure and the replacement process. Always refer to it before starting any replacement.
• Buy Genuine Parts: To ensure the best performance and compatibility, purchase replacement parts directly from authorized suppliers.
• Take Your Time: Rushing through the replacement process can lead to mistakes, such as misconnecting wires or damaging parts. Work slowly and carefully.

Contact Us for Replacement Parts and More

If you're in need of replacement parts for your Yeson vaporizer or have any questions about the replacement process, don't hesitate to reach out to us. As a leading supplier of Yeson vaporizers, we have a wide range of genuine replacement parts in stock. We can also provide you with professional advice and support to make your part - replacement experience as smooth as possible. Whether you're a retailer looking to stock up on replacement parts or an individual user in need of a single component, we're here to serve you.

References

• Yeson Vaporizer User Manuals
• Vaping Industry Technical Guides